Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
Each person seems to have their own individual piece of advice about A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open a wall to remove the old tub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and also embeded in the new one. Ensure you have actually certified yourself for the task and are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to consider employing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This write-up will assist you mount a brand-new bathtub in your restroom if you have already acquired a brand-new bathtub and don't need to alter the arrangement of your previous water supply pipes.
Your devices and also material list need to comprise the following:
Preparing for the Installment
Firstly, the supporting structure provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water system. After doing so, activate the taps to drain any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, put the tub in the required setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub up until the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile faucet connector to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leakages and also tighten them if essential. Fill up the bathtub and additionally check the overflow electrical outlet and the typical outlet for leakages.
Lastly, take care of the bathroom paneling as described in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the bath tub has actually been made use of at the very least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in location in between the tap and the sink. Safeguard the tap in place with the supplier given backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous type needs to be attached to the tap finishes first, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, leading to issues with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can break rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that article about Installing A Bathtub through an associate on our other website. Sharing is good. One never knows, you may be doing someone a favor. Thanks for going through it.
Book A Free Estimate Report this page